Military
Photos show one of three possible modules fittted to a chassis without the optional fan assembly.
Model 3601 Ultra Low Noise, Modular, Rack Mount Power Supply
Input: Nominal 240 Vac, 180 – 305 Vac 50/60Hz.
Output: 3.3 to 18.0 V DC, 30W per output, up to 18 outputs.
Rack mount 19U design, 3U high.
The MIL-Systems Model 3601 ultra low noise, rack mount, modular power supply has been developed for signal processing and amplifier applications where ultra low noise and system up-time are critical requirements. The Model 3601 chassis can accommodate up to three modules with 6 output connectors per module. Each output connector has two outputs, giving a total of 12 outputs per module. Each module can be “hot-swapped” while the remaining modules in the chassis continue to provide uninterrupted power. Modbus serial line communications provide for individual on-off control of each output as well as feedback of status, current draw, temperature and hours of operation. An optional fan assembly provides additional cooling for continuous opera-tion up to 50 0C.
- Operating air temperature at full load 20 ºC to +30 ºC without fan
-20 ºC to +50 ºC with optional fan assemblies. - 6 output connectors per module.
- Up to 3 modules per chassis
- 360 W maximum output power per module
- 1080 W maximum output power
- Low noise performance as standard, Ultra-low noise option available
- EMC to MIL-STD 461G.
- Chassis configurable for connectors on the front or rear panel.
- All output 0V referenced to chassis ground stud.
- Modbus serial line communication.
- All outputs have remote on / off control.
- All outputs have independent overload and short circuit protection with auto-reset.

Battlefield Satellite Terminal Power Supply
1500 W AC/DC
Input: 240 Vac ±10%, 50 Hz ±5%
Output: 28 Vdc 50 A
Rugged sealed construction with anti shock and vibration system.
- Power Factor Corrected Input
- Complies with electrical safety standard AS/NZS60950, MIL-STD-454
- Isolation 3000 Vrms input-output, 1500 Vrms input-chassis
- Complies with EMC standard MIL-STD-461, Class A3. Tested to comply with army TEMPEST requirements
- 19″ rack mountable with intergral shock and vibration absorption system
- Fully sealed to withstand dust, sand, rain and snow
- Temperature compensated battery charging
- Complies with DEF (AUST) 5247 environmental tests
- Operational temperature -19ºC to +44ºC

Battlefield Radio Power Supply
250 W AC/DC & DC/DC
Input: 240 Vac ±10%, 50 Hz ±5%, 28 Vdc
Output: 28 Vdc 10 A
With battery charging. Rugged sealed construction with anti shock and vibration system.
- Power Factor Corrected AC Input
- Isolation 3000 V rms input-output, 1500 V rms input-chassis
- 19″ rack mountable with intergral shock and vibration absorption system. 4 U high 178 mm
- Temperature compensated battery charging
- Triple redundant input automatically switches from AC to DC to battery with no interruption of the output
- Complies with electrical safety standard AS/NZS60950, MIL-STD-454
- Complies with EMC standard MIL-STD-461, Class A3, Power Supplies. Tested to comply with army TEMPEST requirements
- Fully sealed to withstand dust, sand, rain and snow.
- Complies with DEF (AUST) 5247 environmental tests
- Five output connectors, separate battery connector and DC input connector

Fast Charger meeting the requirements specified in DEFD(AUST) 10996, J5285
Input: 210 to 264 VAC, Single phase, 47 to 63 Hz
Output: 25 A at 14.4 V or 28.8 V
Operating Temperature: 5°C to 50°C
The primary role of the Model 6130 12/24V Battery Charger is to facilitate rapid recovery of deeply discharged lead-acid batteries, either as a single 12 V battery or arranged as a 24 V battery bank.
- Rugged, Fanless design
- Sealed enclosure suitable for workshop environment
- Fully rated to DEF (AUST) standards for Land based use in Australia.
- Automatic 12V – 24V battery detection.
- Rapid, boost stage for initial cell charging.
- Intelligent, multi stage, charge control.
- Ergonomic swing handles to facilitate easy vertical carrying.